<strike id="fthll"><dl id="fthll"><del id="fthll"></del></dl></strike>
<span id="fthll"><dl id="fthll"></dl></span><strike id="fthll"></strike>
<strike id="fthll"><i id="fthll"></i></strike>
<strike id="fthll"></strike>
<span id="fthll"><i id="fthll"></i></span>
<strike id="fthll"><dl id="fthll"></dl></strike>
<span id="fthll"><i id="fthll"><del id="fthll"></del></i></span>
<span id="fthll"><dl id="fthll"></dl></span>
<strike id="fthll"><dl id="fthll"><ruby id="fthll"></ruby></dl></strike>

Double acting hydraulic cylind

發布時間:2009-09-20 來源:揚子工具集團 瀏覽次數:67570

    When the combined seal is used,the amount of internal oil leakage shall be
limited up t0 2 times the value舒yen in Table l0.
    In addition,when the piston ring is used,the amount shall be not more
than the value of Attached Fi9.1.
Table l0.Amount of internal oil leakage
Unit:ml,10 min

 Bore oftube
    mm
 
 Amount of
 oil leakage
 
 Bore oftube
 
    mm
 Amount of
 oil leakage
 
 Bore oftube
 
    mITI
 Amount of
 oil leakage
 
 32(3i.5)
    0.2
    100
    2.O
 200
    7.8
    40
    0.3
    125
    2.8
 220(224)
    10.O
    50
    0.5
    140
    3.0
 250
    11.0
    63
    0.8
    160
    5.0
 
    80
    1.3
    180
    6.3

 
5.5 Thrust efficiency When tested in accordance with l0.2.5,the value of
thrust efficiency of the cylinder shall be not less than 0.9.
Informative reference:The value of thrust efficiency varies depending on the
    value of pressure,shape of packings,etc.
6. Construction
6.1 General con8truction
 11
E 8354.1992
6.1.1—Construction—of cylinder    Each part of the same type cylinders i aade by
the same manufacturer shall be interchangeable,and interchanging of t:1e parts
shall not cause remarkable change in their performances.The cylinder shall be
of such construction as to need no special tools at the time of disassemb.ing and
assembling for replacing or inspection of packings,gaskets and so on.
6.1.2一Fixing of rod and piston—The rod and piston shall be fixed secu:ely
together so as neither to loosen nor to allow the adjustment to get out 0’order
during the operation.When screw threads are used for fixing a rod and a pis七on,
the threads shall be in accordance with JIS B 0207,and the accuracy th 3reof
shall be of 6H/6 9 specified in JIS B 0211.
6.1.3—Mountin9—of switch The swish shall be fixed securely to the cy[inder so
as neither to be loosened nor to fall out of adjustment due to vibration.
6.1.4—Interception—of the air The cylinder shall be so constructed tha:the air
does not enter from the joint parts and seal parts.
6.1.5 Names of parts The names of parts of cylinders shall be in acc0:’dance
with Attached Fi9.3.
6.2一—Dust w—iper The gland of the rod cover shall provide a dust wipt腎to
prevent the rod packing from being damaged by external dust and the li【e.‘
6.2.2—P—o——r—t The ports shall be either the threaded joint type or pipe fie nge joint
type as specified in Table 31.
    Screw threads of the screwed end of mating flanges shall be in acc ordance
with JIS B 0203,and those of welding end of mating flanges shall be of;SA
specified in JIS B 229 1,and there shall be no harmful defect in practice on the
mating face.    .
    To the pipe flange fittin9,a mating flange of screwed end or weldi:19 end
shall be attached.
    For the gasket of the pipe flange fittin9,Class l gasket for static l tse speci—
fled in JIS B 2401 should preferably be used.
6.2.3 Cushioning The cylinder containing
should be so constructed as to be adjustable
the cushioning mechanism i:1 itself
by a needle valve and the li:【e.
6.2.4 Head cover。rod cover and piston The head cover,rod cover and piston
shall have robustness sufficient to withstand internal pressure,and the;,land
part(including bush)of rod cover and the piston shall slide smoothly anc【shall
not impair the mutual sliding surfaces even if subjected to the lateral l0;.d of the
rod.As an operating condition,the lateral load of the rod shall be about i/i00
the maximum cylinder force.
6.2.5 Cylinder tube The wall thickness of the cylinder tube,hereafter
refe-rred to as the”tube”,shall be not less than the value obtained from{he for-
mula below,and it shall have ample stiffness.
0:minimum value oftensile strength
 (N/ram2){kgf/cm2}
    When the tube is welded to the rod cover,head cover or the flange,the wall
thickness shall be made thicker,taking into consideration the effect of the weld.
in9.When the inside and outside of the pressure withstanding part of the tube is
machined(including working for steady rest)or threaded,the minimum wall
thickness shall be not less than t obtained as above.In this case,screw threads
shall generally conform to JIS B 0207.
6.2.6 Rod The rod diameter shall be selected on the basis of the buckling of
the rod and the piston speed,and it should be preforable that the rod is processed
with the width across flats for wrenchin9.The width across flat dimensions
should be as specified in JIS B l002.
    The sliding part shall be processed with the electroplated coatings of chr0.
mlum tor engmeenng Purpose tor preventing tlaWS,nicks,rust,etc.
6.2.7.M.......o....u.....n.....t...i...n.....g.......p.....a....r....t..—s—The mounting parts shall be those of having sufficient
rigidity against reaction force due to operation,and furthermore shall meet the
following requirements:    ‘    +
(1)The attaching face of the mounting part of the foot type cylinder shall be in
    parallel with the centre line of the cylinder.
(2)The attaching face of the mounting part of the flange type cylinder shall be
    at right angles to the centre line of the cylinder.    、
(3)The attaching face of the mounting part of the crevice type cylinder shall be
    in parallel with the plane of swing of the cylinder,and the centre line of
    hole shall pass through the centre line of the cylinder and be at right angles
    to the plane of swin9.
(4)The attaching shaft of the mounting part of the trunnion type cylinder shall
    be symmetrical with respect to the centre line of the cylinder,and shall be
    at right angles to it.
6.2.8 Switch
that the piston
electric circuit
electric circuit
 The switch shall be of a dip—proof type,and when it has sensed
 is approachin9,an indicator light is lighted at the same time the
is closed,and when the piston has separated from the switch,the
is opened to put out the indicator light.
I’ube bores and rod diameter8
rod diameters shall be as given
 y.
 勱e basic dimensions
in Table l l according to
    13
B 8354.1992
of the tube)ores and
the series A,B,C,五
    If it is difficult to follow the first choice of the dimensions due to st,eed.
buckling and the like,select the second choice.
    Tolerances,circularities and cylindricities on the finished dimensi0『】IS of the
tube bores and the sliding portion of the rod shall conform to Table l2 fl ad Table
13 with respect to the basic dimensions.
Table l l.Basic dimensions of tube bores and rod diameters

 
    1st choice
    2nd choice
 Tube bore
    Rod bore symbols
    A
    B
    C
    X
 
    32(31.5)
 22(22.4)
 18
 14
 20
 
    40
 28
 22(22.4)
 18
 25
 
    50
 36(35.5)
 28
 22 (22.4)
 32 (31.5)
 
    63
 45
 36(35.5)
 28
 40
 
    80
 56
 45
 36 (35.5)
 50
 
 100
 70 (71)
 56
 45
 63
 
    125
    90
    70(71)
    56
    80
    t
    140
 100
    80
    63
    90
 
    160
 110 (112)
    90
    70 (71)
 100
    {
    180
 
 125
 
 100
 
 80
 
 110(112)
 
    l
    ‘
    200
 140
 Ii0(112)
 90
 125
 1I
 220(224)
 160
 125
 100
 140
 1:
    250
 180
 140
 110 (112)
 160
 1:

Remarks l.Numerical values given in parentheses should not be used,as faj as pos-
    sible.
Combination of a tube bore and a rod diameter shall be selected{Lccording
to nominal pressure,length of stroke and rod material.
The values of piston-rod diameter and bore diameter which are n 3t in
accordance with this Table shall be selected from JIS B 8366.
14
B 8354.1992
Table l2.Finished dimenmons of tube bores
Unit:mm

 
 
    When piston ring is used
 When packing other than
    Plston nng is used
    。I、lbe bore
 
 
 TOlerance on
 finished
 dimension
 
 Circularity
 
 
 Cyhndricity
 
 Tolerance on
    finished
 dimension
 Circularity
    and
 cylindricity
 
 32 40 50
 
 +0.025
 
    0
    0.019
 
 
    0.025
 
 
    +0.062
 
    0
 
    0.062
 
 
    63 80
    +0.030
    0 .
    0.Ol9
 
    0.030
 
    +0.074
    O
    0.074
 
 
 100
 +0.035
    0
    0.022
 
    0.035
 
    +0.087
    O
 
    0.087
 
 125 140 160 180
    +0.040
    O
    0.025
 
    0.O40
 
    +0.100
    0
    0.100
 
 
 200 220 250
    +0.046
    O
    0.029
 
    0.046
 
    +0.115
    0
 
    0.115

 

本文鏈接: http://www.horygine.com/yzgjcn_172.html
如需轉載請注明:中工工業液壓千斤頂http://www.horygine.com

本文章總10頁 上一頁 1 2 3 4 5 6 7 8 9 10 下一頁

上一篇:伸縮式套筒液壓缸
下一編:液壓接頭和插頭尺寸規范
千斤頂相關知識
液壓傳動概述
液壓泵工作原理
液壓系統系統的組成和表示方法
液壓千斤頂原理、發明、簡介、工作原理圖
抗磨液壓油的特性及選用
液壓千斤頂高壓膠管、高壓硬管外徑參考
液壓千斤頂相關產品(請點擊產品名稱查看詳細資料)
電動千斤頂(中工F-V50-1000T) - 同步千斤頂 - 電動液壓頂(中工F-Q頂管機大行程) 大噸位分離式液
壓頂
薄型千斤頂(噸位5-200T行程6-80mm) - 同步薄型千斤頂(薄型中工B-V)
橋梁千斤頂(中工M-B) - 超薄型千斤頂(RSM5-150T) - 薄型千斤頂(RCS5-100T)
空間窄小-如橋梁
更換支座
穿心千斤頂(中工H-C空心頂) - 空心千斤頂(RCH穿心頂) - 雙作用空心千斤頂(RRH) 具有拉伸功能空
心液壓頂
自鎖千斤頂(中工L-V50-1080T) - 自鎖同步千斤頂 - 自鎖式千斤頂(CLL) 需長時間支撐重
物液壓頂
分離式千斤頂(10-200T) - 手動液壓千斤頂(5-100T) - 多節千斤頂 小噸位分離式液
壓頂
超高壓大噸位千斤頂(CLR) - 電動液壓千斤頂(DYG) - 大噸位液壓千斤頂(CLS) 大噸位液壓頂舊
型號
電動油泵(中工B-V電動泵站) - 手動泵(YSB單向) - 雙向手動油泵(YSSB) - 手動油泵(YCSB)
液壓千斤頂選型調查表(在括號中填上數據,并留下聯系方法,最后再提交)
單位:
姓名:
電話:
傳真:
手機:
郵箱:
精品国产情侣高潮露脸在线_h肉动漫无码无修在线观看下载_五月婷婷久久_日本成熟妇人高潮A片免费_艳星juliaann黑人开战