<strike id="fthll"><dl id="fthll"><del id="fthll"></del></dl></strike>
<span id="fthll"><dl id="fthll"></dl></span><strike id="fthll"></strike>
<strike id="fthll"><i id="fthll"></i></strike>
<strike id="fthll"></strike>
<span id="fthll"><i id="fthll"></i></span>
<strike id="fthll"><dl id="fthll"></dl></strike>
<span id="fthll"><i id="fthll"><del id="fthll"></del></i></span>
<span id="fthll"><dl id="fthll"></dl></span>
<strike id="fthll"><dl id="fthll"><ruby id="fthll"></ruby></dl></strike>

Double acting hydraulic cylind

發布時間:2009-09-20 來源:揚子工具集團 瀏覽次數:67578

Remarks l.Circularity here shall be expressed as the difference between the maxi-
    mum diameter and the minimum diameter at an arbitrary section of a
    tube,and the maximum value of circularity throughout the whole length of
    the tube shall not exceed the value given in this Table.
2.Cylindricity here shall be expressed as the difference between the maxi—
 mum diameter and the minimum diameter measured throughout the
 whole length of the tube.
3.Bending of the tube shall be not more than l mm per l000 mlTl.
Table l3.Finished dimensiOIlS of rods
Unit:mm

    Rod diameter
    Tolerances on
 finished dimension
 Circularity and
 cylindridty
    lO l2 14 16 18
    —0.016
    —0.O43
    0.027
 
    20 22 25 28
    ——0.020
    —0.053
    0.033
 
 32 36 40 45 50
 
    —0.025
 
    一O.064
 
    0.o39
 
 
    56 63 70 80
 
    ——0.030
 
    —0.076
 
    0.046
 
 
 90 100 110 125
 
    —0.036
 
    一O.O90
 
    0.054
 
 
 140 160 180
 
    —0.O43
 
    —0.106
 
    0.063
 

15
B 8354.1992
Remarks l.Circularity here shall be expressed as the difference between the maxi-
    mum diameter and the minimum diameter at an arbitrary sectic fl of a rod,
    and the maximum circularity throughout the whole length of the rod shall
    not exceed the value given in this Table.
2.Cylindricity here shall be expressed as the difference between th≥maxi-
 mum diameter and the minimum diameter measured throughou:the
 whole length of the rod.
3.Bending of the rod shall be not more than 0.25 mm per l000 mm
7.2—Finish of sl—iding faces The finish of the tube inside face,sliding faces of
the rod and bush shall be expressed by the center line mean roughness,and shall
be approximately the roughness of Table l 4.
Table l4.Finish of sliding faces

    Division according to sliding face
    and applicable packing
 
    Surface roughness
 
 Rubber
 0.4a(1.6S)
 Sliding face of rod to
 packing
 Fabric reinforced
 rubber
 
 0.8 a(3.2S)
 Others
 0.8 a(3.2 S)
 
 Rubber
 0.4 a(1.6 S)(3)。0.8 a(3.2 S)
S1iding face of tube
 
Fabric reinforced
 rubber
 
 0.8 a(3.2S)
 reside to paclcmg
 
 
 Metal
 
 0.4 a(1.6 S)
 Others
 0.8 a(3.2 S)
 Sliding face of pison
 0.8 a(3.2S)
 Sliding face of bush
 1.6 a(6.3 S)

 
Note(3) When 0-ring or X-ring is used.
Remarks l.Surface roughness shall be as defined in JIS B 0601.
    2.Surface roughness given in parentheses should not be used as
    far as possible.
7.3.Stroke length The stroke lengths shall be in accordance with Tat le l5,
and the tolerances thereof shall be in accordance with Table l6.
    Even if Table l 5 is not applicable,it should preferably be in accord ance with
the provisions of JIS Z 8601.
Unit:mm
7.4
Table l6.Tolerances on stroke lengths
Unit:mm

 
    Tolerances
    Stroke length
    Division
    GradeA
    GradeB
 
 i00 and under
 
    +0.8
 
    O
    +1.6
 
    0
 
 Over i00 up to and incl.250
 
    +1.O
 
    O
    +2.5
 
    O
 
 Over 250 up to and incl.630
 
    +1.25
 
    0
    +4.O
 
    0
 
 Over 630 up to and incl.i000
 
    +1.4
 
    O
    +5.0
 
    O
 
 Over l000 up to and ind.1600
    +1.6
    0
    +6.3
    O
 
 Over l600 up to and incl.2000
    +1.8
    O
    +8.0
    0

 
tube end face and fitting face of the cylinder cover
more than 0.04 mm.
The perpendicularity of the
to the shaft axis shall be not
7.5—Perpendicularity and—coaxiality of piston The perpendicularity of end face
of a piston body to its shaft axis shall be not more than 0.04 mm,and the
coaxiality of sliding face to the piston shaft axis shall be not more than 0.03 mm.    、.,,
7.6 Fits of piston and tube The fits of the sliding face of the piston and that
of the tube having been subjected to turning or honing should be of H 7/g 7 speci.
fled in JIS B 0401 for the piston using piston rin9,and be of H 9/f 8 for that
using packin9.For the tube having been subjected only to honin9,it is allowed to
use for the piston using packing SO long as it has the same clearance as the fit of
H 9/f 8 within the range of Table ll and Table l2.
7.7
and
 Fits of bush and rod The fits of the bush(or a part corresponding to it)
the rod should conform to H 9/f 8 specified in JIS B 040 1.
7.8.1 Screw threads of rod end The screw
fine threads specified in JIS B 0207,and the
diameter shall conform to Table l7(A).
threads of rod end shall be of metric
dimensions with respect to the rod
17
B 8354.1992
    However,if Table l7(A)is not applicable,Table l7(B)should aW ly.
    The permissible dimensional deviation and tolerance shall confoFIE t0 6 9
specified in JIS B 021 1.
    When screw threads with pitches longer than those given in Table l7(A)
and Table l7(B)are used,it is recommended to select them among thos≥speci.
fied in Table l7(C).
Table l7(A)Screw thread of rod end

 
 Rod diameter
 
 Nominal
 designation 01"
screw thread
 Length of
 screw—thread
 
 
 Rod diameter
 
    Nominal
 designation of
 screw thread
    I
 8Cr
 
    10(11.2)
M 8×1
    12
    50
 M 45×1.5
 
    12(12.5)
M 10 X 1.25
    15
    56
 M 48 X 1.5
 
    14
 M 12 X 1.25
    18
    63
 M 56×2
 
    16
 M 14 X 1.5
    20
    70(71)
 M 64 X 2
 
    18
 M 16 X 1.5
    25
    80
 M 72×2
 
    20
 M 18 X 1.5
    27
    90
 M 80×2
 
 22(22.4)
M 20 X 1.5
    30
 100
 M 95 X 2
 
 25
 M 22×1.5
    33
 110(112)
 M i00 X 2
 
    28
 M 24×1.5
    35
    125
 M 120 X 2
 
    32(31.5)
M 27×1.5
    40
    140
 M 130 X 2
 
    36(35.5)
M 30×1.5
    45
    160
 M 150 X 2
 
 40
 M 33×1.5
    50
    180
 M 170 X 2
 
 45
 M 39×1.5
    60
 

 
Table l7(B)Screw thread of rod end

 
 Rod diameter
 
 Nominal
 designation ot
 screw thread
 Length of
 screw thread
 
 
 Rod diameter
 
    Nominal
 designation of
 screw thread
    L
 Scr
 
    10(11.2)
M 8 X 1
    12
    50
 M 39×1.5
 
 12(12.5)
M 8 X 1
    12
    56
 M 42 X 1.5
 
    14
 M 10 X 1.25
    15
    63
 M 48 X 1.5
 
    16
 M 12 X 1.25
    18
    70(71)
 M 56×2
 
    18
 M 14 X 1.5
    20
    80
 M 60 X 2
 
    20
 M 16 X 1.5
    25
    90
 M 68 X 2
 
 22(22.4)
M 18 X 1.5
    27
 100
 M 76 X 2
 
    25
 M 20 X 1.5
    30
 110(112)
 M 85 X 2
 
    28
 M 22 X 1.5
    33
    125
 M 90×2
 
 32(31.5)
M 24 X 1.5
    35
    140
 M 100 X 2
 
 36(35.5)
M 27 X 1.5
    40
    160
 M 120 X 2
 
    40
 M 30×1.6
    45
    180
 M 130 X 2
 
    45
 M 33×1.5
    50
 

18
B 8354.1992
 Table l7(C)Screw thread of rod end
Unit:mm

 Nominal desig-
natlon oi screw
    thread
 Nominal desig-
na鈕on oI screW
    thread
 M 3×0.35
 M 4×0.5
 M 5×0.5
 M 6×0.75
 M 8×1
 M 10×1.25
 M 12×1.25
 M 14×1.5
 M 16×1.5
 M 18×.l.5
 M 20×1.5
 M 22×1.5
 M 24×2
 M 27×2
 M 30×2
 M 33×2
 M 36×2
 M 42×2
 M 48×2
 M 56×2
 M 64×3
 M 72×3
 M 80×3
 M 90×3
 M i00×3
 M 110×3
 M 125×4
 M 140×4
 M 160×4
 M 180×4
 M 200×4
 M 220×4
 M 250×6
 M 280 x 6

 
Informative reference:The nominal designations of screw threads conform
    to those specified in IS0 4395:1978
7.8..2—Pin holes a—t rod ends The dimensions of the pin holes at rod ends shall
conform to Table l8.

 

本文鏈接: http://www.horygine.com/yzgjcn_172.html
如需轉載請注明:中工工業液壓千斤頂http://www.horygine.com

本文章總10頁 上一頁 1 2 3 4 5 6 7 8 9 10 下一頁

上一篇:伸縮式套筒液壓缸
下一編:液壓接頭和插頭尺寸規范
千斤頂相關知識
液壓缸工作時出現爬行現象的原因及排除方法
缸體、活塞和活塞桿的材料
盾構法頂涵施工工藝
液壓千斤頂及膠管的清潔度指標
液壓油缸支承襯套的材料及裝配部位和裝配間隙
液壓傳動的應用及其發展前景
液壓千斤頂相關產品(請點擊產品名稱查看詳細資料)
電動千斤頂(中工F-V50-1000T) - 同步千斤頂 - 電動液壓頂(中工F-Q頂管機大行程) 大噸位分離式液
壓頂
薄型千斤頂(噸位5-200T行程6-80mm) - 同步薄型千斤頂(薄型中工B-V)
橋梁千斤頂(中工M-B) - 超薄型千斤頂(RSM5-150T) - 薄型千斤頂(RCS5-100T)
空間窄小-如橋梁
更換支座
穿心千斤頂(中工H-C空心頂) - 空心千斤頂(RCH穿心頂) - 雙作用空心千斤頂(RRH) 具有拉伸功能空
心液壓頂
自鎖千斤頂(中工L-V50-1080T) - 自鎖同步千斤頂 - 自鎖式千斤頂(CLL) 需長時間支撐重
物液壓頂
分離式千斤頂(10-200T) - 手動液壓千斤頂(5-100T) - 多節千斤頂 小噸位分離式液
壓頂
超高壓大噸位千斤頂(CLR) - 電動液壓千斤頂(DYG) - 大噸位液壓千斤頂(CLS) 大噸位液壓頂舊
型號
電動油泵(中工B-V電動泵站) - 手動泵(YSB單向) - 雙向手動油泵(YSSB) - 手動油泵(YCSB)
液壓千斤頂選型調查表(在括號中填上數據,并留下聯系方法,最后再提交)
單位:
姓名:
電話:
傳真:
手機:
郵箱:
精品国产情侣高潮露脸在线_h肉动漫无码无修在线观看下载_五月婷婷久久_日本成熟妇人高潮A片免费_艳星juliaann黑人开战